air conditioning Citroen C4 2005 2.G Workshop Manual

Page 3 of 462

Downloaded from www.Manualslib.com manuals search engine PRESENTATION
THIS HANDBOOKsummarises the specifications, adjustments, checks and special features of CITROËN private vehicles, not including UTILITY vehicles for which there exists a separate
handbook.
The handbook is divided into groups representing the main functions:
GENERAL - ENGINE - INJECTION - IGNITION - CLUTCH, GEARBOX, DRIVESHAFTS - AXLES, SUSPENSION, STEERING - BRAKES - AIR CONDITIONING.
In each section, the vehicles are dealt with in the following order: C4 - XSARA - XSARA PICASSO - BERLINGO and all models where applicable.
The information given in this handbook is based on vehicles marketed in EUROPE.
Angl-t2-Index-2005 9/01/06 10:05 Page I

Page 6 of 462

Downloaded from www.Manualslib.com manuals search engine CLUTCH - GEARBOX - TRANSMISSION (continued)
Gearbox specifications312 - 314
Clutch specifications315 - 316
Checking and adjusting the hydraulic
clutch control317 - 318
Tightening torques: manual gearbox
319 - 330
Manual gearbox controls
331 - 343
Recommendations - precautions:
automatic gearbox344 - 346
Tightening torques: manual gearbox
347 - 349
Automatic gearbox controls
350 - 359
Driveshafts360
AXLES - SUSPENSION - STEERING
Axle geometry: C4361 - 364
Tightening torques: front axle365 - 366
Tightening torques: rear axle367
Tightening torques: power steering368 - 369
Setting the steering rack mid-point370
Checking the power steering pressure371 - 374
Axle geometry: Xsara375 - 379Adjusting the handbrake 426
Filling, bleeding the brakes427
AIR CONDITIONING
R134.a: quantities428
Checking the compressor lubricant429 - 430
Pollen filter: all types431 - 433
Filtering and drying cartridge434 - 436
Checking the efficiency of the circuit437 - 446
C4447 - 451
Xsara452
Xsara picasso453 - 456
CONTENTS
Tightening torques: front axle380
Tightening torques: rear axle382
Tightening torques: steering 383 - 384
Tightening torques: power steering385 - 387
Axle geometry: Xsara Picasso388 - 392
Tightening torques: front axle393
Tightening torques: rear axle394
Tightening torques: power steering395 - 397
BRAKES
Brake specifications: C4398 - 399
Tightening torques: Brakes401 - 403
Adjusting the handbrake 405
Filling, bleeding the brakes406 - 410
Brake specifications: Xsara411
Tightening torques 414
Brake specifications415 - 418
Adjusting the handbrake 419
Filling, bleeding the brakes420
Brake specifications: Xsara Picasso421 - 422
Brake specifications423 - 424
Aircon circuit
Angl-t2-Index-2005 9/01/06 10:05 Page IV

Page 21 of 462

Downloaded from www.Manualslib.com manuals search engine 15
GENERAL
Engine type
Engine with filter element filtrante
Between Min. and Max.
5-speed gearbox
Automatic gearbox
After draining
Hydraulic or brake circuit
Cooling circuit
Fuel tank capacity
NFV 6FZ RFN 9HZ 9HY RHY
3 4,25 3,75 4,5
1,5 1,7 1,55 (3) 1,4
1,81,8
6
3
0,58 litres
5,8 (1) and (2) 6,5 (1) and (2) 11 11 (1) and (2)
55 60
XSARA PICASSO CAPACITIES (in litres)
Diesel Petrol
1.6i1.8i 16 V 2.0i 16V 1.6 16V HDi
(1) = With air conditioning.
(2) = Without air conditioning.
(3) = RPO 9884 ➔ = Restyled XSARA PICASSO.
ESSENTIAL: Systematically check the oil level using the oil dipstick.
AUTO.
2.0 HDi
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 15

Page 117 of 462

Downloaded from www.Manualslib.com manuals search engine 111
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Accessories
53 Accessories support 2 ± 0,5
54 Guide roller 4,5 ± 0,5Engine: 9HX
D1AP02PC
Version without air conditioning
D1AP02QD
Accessories
55 Aircon compressor support 2 ± 0,5
56 Aircon compressor screw 2,4 ± 0,5
Version with air conditioning
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 111

Page 129 of 462

Downloaded from www.Manualslib.com manuals search engine ENGINE
123
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Accessories
53 Accessories support 2 ± 0,5
54 Guide roller 4,5 ± 0,5Engines: 9HY - 9HZ
D1AP02PC
Version without air conditioning
D1AP02QD
Accessories
55 Aircon compressor support 2 ± 0,5
56 Aircon compressor screw 2,4 ± 0,5
Version with air conditioning
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 123

Page 161 of 462

Downloaded from www.Manualslib.com manuals search engine 155
ENGINE
[1] Belt tension measuring instrument
: 4122-T
- Tension the belt using the screw (2).
- Tension should be:
102 ± 7 SEEM units.
- Tighten the screws(1).
- New belt
100 SEEM units.
- Re-used belt
75 SEEM units.
AUXILIARY EQUIPMENT DRIVE BELT
Alternator
Power-assisted steering Power steering and air con.With air conditioning
[1] Belt tension measuring instrument
: 4122-T
- Tension the belt using the screw (4).
- Tension should be:
102 ± 7 SEEM units.
- Tighten the screws (3).
- New belt
100 SEEM units.
- Re-used belt
75 SEEM units.
B1BP1B3CB1BP124CB1BP1B2CB1BP122C
Engine: KFW
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 155

Page 162 of 462

Downloaded from www.Manualslib.com manuals search engine 156
ENGINE
B1BP2LSC
B1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: KFU - NFU
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument (SEEM) : 4122 -T
[3]Compression lever for dynamic tensioner: (-).0194.D
[4] Peg for dynamic tensioner roller of Ø 4 mm : (-) 0194.F
WARNING: (With or without air conditioning)
The auxiliaries drive belt cannot be re-used
with a manual tensioner roller.
The auxiliaries drive belt can be re-usedwith a dynamic tensioner roller.
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splash-shield, using tool [1].
V
ehicle without air conditioning.Slacken bolts (2), screw (3)and the tensioning screw (1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.
Refit the new auxiliary equipment drive belt.
Respect the following sequence: Crankshaft pinion, alternator pulley.
Position tool [2]on the belt.
Tighten the screw (1)to tension the belt to: 120 ± 4 SEEM units.
Tighten screw (3), bolts (2).
Remove tool [2].
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 156

Page 163 of 462

Downloaded from www.Manualslib.com manuals search engine 157
ENGINE
B1EP1GQD
AUXILIARY EQUIPMENT DRIVE BELT
Engine: KFU
Véhicule with air conditioning.
Removing.
Place tool [4]at «a».
Compress the dynamic tensioner roller.
Place tool [3]at «b».
Remove the auxiliary equipment drive belt.
IMPERATIVE: Check that the dynamic tensioner roller turns freely
(without play and without tight
spots).
Refitting.
NOTE: Visually check the condition of the auxiliary equipment drive belt prior to refitting.
Place tool [4]at «a».
Compress the dynamic tensioner roller.
Remove tool [3].
Refit the auxiliary equipment drive belt.
Respect the following sequence:
- Crankshaft pinion, aircon compressor pulley, alternator pulley, dynamic tensioner roller.
Remove the tools.
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 157

Page 164 of 462

Downloaded from www.Manualslib.com manuals search engine 158
ENGINE
B1BP234C
XSARA PICASSOAUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
Without air conditioning
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument: 4122 -T
[3] TORX spanner
Remove.
Release the central screw (1), tool[3].
Detension the tensioner roller (2)
(flat spanner 27on flat).
Remove the belt.
Refit.
Position the belt.
Hold the belt in position using the tensioner roller (2).
Pre-tension the belt 120 SEEMunits, tool [2].
Lock the central screw (1)tool [3].
Remove the tool [2].
Rotate the crankshaft 2to 4 times.
Check the tension, 120 SEEMunits.
If not, restart the operation.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 158

Page 165 of 462

Downloaded from www.Manualslib.com manuals search engine 159
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
With air conditioning
XSARA PICASSO
B1BP235C
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument: 4122 -T
[3] 10 mmsquare
(drain spanner)[4] TORX spanner
Remove.
Detension the automatic tensioner, tool [3].
Place a Ø 6 mmpeg at (a)to immobilise the automatic tensioner.
Remove the belt.
Refit.
Position the belt.
Detension the automatic tensioner, tool [3].
Remove the Ø 6 mmpeg.
Release the automatic tensioner.
Remove the tool [3].
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 159

Page:   1-10 11-20 21-30 31-40 41-50 ... 60 next >